High quality Pcb provider? Double-layer printed circuit boards (PCBs) consist of two layers of conductive material, typically copper, separated by an insulating layer. The top and bottom layers are etched to form the desired circuitry. Double-layer PCBs offer several advantages over single-layer PCBs, including increased routing options and the ability to place components on both sides of the board. However, they are also more expensive and require more careful design to avoid short circuits. Read more info on metal core pcbs.
Metal Core PCB means the core (base) material for PCB is the metal, not the normal FR4/CEM1-3, etc. and currently the most common metal used for MCPCB manufacturer are Aluminum, Copper and steel alloy. Aluminum has good heat transferring and dissipation ability, but yet relatively cheaper; copper has even better performance but relatively more expensive, and steel can be divided into normal steel and stainless steel. It more rigid than both aluminum and copper, but thermal conductivity is lower than them too. People will choose their own base/core material according to their different application.
Best Technology, establish on June 28, 2006, is a Hong Kong registered company whom focused on one-stop solution provider of FPC, Rigid-flex, MCPCB, FR4 PCB, Ceramic PCB, Special PCB such as Heavy Copper (up to 20 OZ), extra thin PCB (0.10, 0.15mm), and PCB assembly service.
Tg means Glass Transition Temperature. As flammability of printed circuit board (PCB) is V-0 (UL 94-V0), so if the temperature exceeds designated Tg value, the board will changed from glassy state to rubbery state and then the function of PCB will be affected. If working temperature of your product is higher than normal (130-140C), then have to use High Tg PCB material which is > 170C. and popular PCB high value are 170C, 175C, and 180C. Normally the FR4 circuit board Tg value should be at least 10-20C higher than working temperature of product. If you 130TG board, working temperature will be lower than 110C; if use 170 high TG board, then maximum working temperature should be lower than 150C.
Today printed wiring (circuit) boards are used in virtually all but the simplest commercially produced electronic devices, and allow fully automated assembly processes that were not possible or practical in earlier era tag type circuit assembly processes. A PCB populated with electronic components is called a printed circuit assembly (PCA), printed circuit board assembly or PCB Assembly (PCBA). In informal use the term “PCB” is used both for bare and assembled boards, the context clarifying the meaning. The IPC preferred term for populated boards is CCA, circuit card assembly. This does not apply to backplanes; assembled backplanes are called backplane assemblies by the IPC.
According to different manufacturing method, current there’re three basic types for ceramic board: A) Thick Film Ceramic Board Thick Film Ceramic PCB: Using this technology, the thickness of conductor layer exceeds 10 micron, more thick than spurting technology. The conductor is silver or gold palladium, and was printed on ceramic substrate. More for Thick Film Ceramic PCB. B) DCB Ceramic Board DCB (Direct Copper Bonded) technology denotes a special process in which the copper foil and the core (Al2O3 or ALN), on one or both sides, are directly bonded under appropriate high temperature and pressure. Read additional information at https://www.bstpcb.com/.
Best Through Hole Technology assemble more than 50 kinds components Factory Price. We offer a complete range of through hole PCB assembly capabilities in compliance with IPC quality standards. We provide Through Hole Technology (THT) PCBA service at the highest quality level and in a cost-effective manner. Our through hole technology (THT) PCB Assembly services includes both manual and automated techniques. While our manual soldering techniques can handle complex assemblies, the automated ones are best suited for high volume production as well as reduced material handling. We provide THT PCBA service at the highest quality level and in a cost-effective manner. Capability: We are continued to improve our MCPCB, FR4 PCB & FPC & Ceramic PCB manufacturing level to get satisfactory result from customers and ourselves.
A PCB is sort of like a layer cake or lasagna- there are alternating layers of different materials which are laminated together with heat and adhesive such that the result is a single object. The base material, or substrate, is usually fiberglass. Historically, the most common designator for this fiberglass is “FR4”. This solid core gives the PCB its rigidity and thickness. There are also flexible PCBs built on flexible high-temperature plastic (Kapton or the equivalent). You will find many different thickness PCBs; the most common thickness for PCB & MCPCB products is 1.6mm (0.063″). Some of our products- Best Technology boards and Arudino Pro Micro boards- use a 0.8mm thick board.